A flying finish!

a-flying-finish
a-flying-finish

With its core competencies focused on structural adhesives and surface treatments, Henkel's Bjorn Ballien discusses the solutions the company has on offer for aircraft exterior surfaces. Mike Richardson reports.

With its core competencies focused on structural adhesives and surface treatments, Henkel’s Bjorn Ballien discusses the solutions the company has on offer for aircraft exterior surfaces. Mike Richardson reports. Of the five senses, perhaps our sense of touch gives us one of the closest indications of perceived quality. Run your hand over the composite airframe of an aircraft and the likelihood is that it will feel smooth and defect-free. To further improve this finish, specialised surface coatings can be applied, and it’s here that Henkel’s portfolio of products and applications for its aerospace customers come into their own. The company’s lightweight surfacing films for composite materials are said to offer a smooth, aerodynamic surface and advanced protection against lightning strikes. The company unveiled its lightweight Loctite EA 9845 Aero surfacing films which can be co-cured with epoxy based composite prepregs at 120-175°C to provide an excellent surface finish under autoclave and even vacuum only cure. The surfacing and lightning strike versions of these films protect the underlying composite materials and are said to enhance environmental resistance to UV and paint stripper exposure. Loctite EA 9845SF Aero is said to offer up to 30% weight savings compared to current surfacing films, whilst a reduction in manufacturing cost and process time is obtained through the elimination of filling and sanding steps during surface preparation. “Our products are designed to improve the surface quality of monolithic and honeycomb composite parts, and offer a durable, paintable surface with minimal surface preparation,” begins Bjorn Ballien, Henkel’s EMEA business development manager aerospace. “The surfacing film is a thin epoxy layer that is applied to the exterior of the aircraft to protect the composite and to fill pin holes and voids to create a surface that can be painted on. “Aircraft exterior composite materials can sometimes contain surface texture and small defects, which during the life of the aircraft could be exposed to different chemicals, like paint strippers, and to repair processes. Applying a thin layer of epoxy improves the surface quality and acts as a protective layer, which also improves the paintability. In certain industries it’s fashionable to see the aesthetic appearance of carbon fibre weave, but the aerospace industry does not follow this trend because the composite material’s surface must be optimised for aerodynamics and to take coatings of primer and paint.” Protection from the elements Meanwhile, Loctite EA 9845LC Aero is claimed to provide the same high quality surface finishing with the lightning strike protection. This film includes lightweight, expanded copper or aluminium mesh for maximum electrical conductivity and protection of aircraft composite parts. The use of an integrated lightning strike solution reduces the number of materials to be inventoried and provides manufacturing cost reduction. As with the surfacing films the Loctite EA 9845LC Aero lightning strike materials are said to provide excellent surface finish when cured under autoclave or vacuum only conditions. The lightning strike films are available in a variety of film and foil weights to meet the requirements of different lightning strike zones on the aircraft. “Henkel’s new generation of Loctite EA 9845LC Aero offers improved surface qualities,” states Ballien. “The product is designed to completely fill and smooth out any potential void or defect. In addition to surfacing, this product provides lightning strike protection. If a predominantly composite-built aircraft is struck by lightning there needs to be a safe method of conducting the electrostatic charge away. Henkel has produced a film that combines with thin copper or aluminium foils that are embedded into the surfacing film itself. Up until now, lightning strike films have required heavier surfacing film areal weights and significant re-work to fill and smooth the surface to meet aerodynamic surface requirements. The Loctite EA 9845 provides the same high quality surface finish and lightning strike protection when cured with only vacuum pressure.” Ballien adds that the new generation of Loctite EA 9845LC Aero also offers airframe OEMs potential time and cost savings in order to meet the increasing production rates. “In the past the airframer would need to use a much thicker film in combination with the copper or aluminium foils, because the thickness of epoxy layer needed to be sufficient enough to prevent the metallic foil from protruding out of the surface,” notes Ballien. “Due to the high surface quality and controlled-flow ability, it completely encapsulates the foils and is much better than the previous versions. Customers can now obtain a much lighter weight version – up to a 30% reduction in weight.” UV comes to light According to Ballien, all Henkel’s products undergo the same rigorous qualification and testing requirements, plus there is a huge amount of mechanical testing that examines erosion resistance, fluid resistance, and chemical exposure, etc. “A key difference between Loctite EA 9845LC Aero and the previous generation of surfacing films currently being used is that the new Loctite EA 9845 Aero offers an enhanced ultraviolet (UV) resistance,” he continues. “During aircraft production, large exterior aircraft surfaces and components are stored in factories under UV lighting, or stored outside in direct sunlight. All the epoxy substances will change colour and the surface can degrade after a certain amount of UV exposure. Our new product has been developed with improved resistance to UV exposure, so the colour and surface characteristics won’t change in a factory environment. “Another key environmental factor with this product is that if you consider the lifecycle of the aircraft, the first paint job the aircraft receives isn’t always the one that sees it through its entire lifecycle. Airline operators may update livery or re-paint the entire aircraft. When an aircraft is sold or leased, the new operator will often change the paint schemes. Prior to repaint these aircraft go through paint stripping on the MRO side of the industry. The first generation of surfacing products weren’t developed to resist the paint strippers. The paint stripper contained chemicals that could attack the surface, whereas our new surfacing film is resistant to paint stripper.” If Henkel’s product really is so good, I finish by asking Ballien whether there is the possibility that customers can simply use copious amounts of 9845LC to hide any imperfections. “The ideal is that eventually we’ll be able to manufacture composites parts so perfectly that they won’t even need any surfacing products. However, the reality is that composite materials will always need to be protected – so these films serve an important purpose,” he concludes. “The first generation of films often contained quality issues after the cure cycle, such as pin holes, voids and other defects that required a lot of rework. The part would often need to be repaired using another adhesive and potting material to touch up all these defects. Loctite EA 9845 Aero will drastically reduce the amount of additional manual labour involved with the surface film of an aircraft.” www.henkel-adhesives.com Captions/images: As OEMs design and build more lightweight aircraft with composite parts and structures, the need for more user-friendly and proven bonded repair solutions becomes a major focus (Photo: Getty Images) Bjorn Ballien of Henkel

Related Articles

Offshore opportunities

The landscape of the UK's energy network is literally changing as the Government looks to the sea with plans to make the country a world leader in offshore wind. With the market swinging into action
12 years ago Features

A vehicle for progress

In attempting to define the state of composites within the UK's automotive sector it is tempting to concentrate on the highly successful motorsport
12 years ago Features

Standing the test of time

Pierangelo Campagna, Exova's technical director for polymers and composites, looks at how the company is anticipating and meeting future demand for composites in the global aerospace sector.
11 years ago Features
Most recent Articles

Exel secures deal with Chinese bus builder

Finnish composite manufacturer Exel Composites has secured a new project with Chinese automotive manufacturer Foton Bus and Coach Company to supply pultruded glass fibre composite profiles.
6 hours ago News

Zünd establishes branch in Australia

Zünd Systemtechnik has announced the establishment of its own branch in Australia. Zund Australia will be based in Melbourne serving existing and new customers from all areas of application in which Zünd is active.
1 day ago News

Login / Sign up